Technovit-2-Bond / 16239
The fast, 2-part PU adhesive for hoof treatment!

The benefits at a glance:

• dries within 30 seconds
• can be used at a 45° and a 90° angle
• the hoof can bear full weight again after approx. 3 minutes (if stored correctly over 15° C)
• bonds powerfully and permanently to wood and rubber blocks
• easy to use - no mixing, no waste

Here's how simple it is to use: Remove the seal on the cartridge and connect up the mixing tip. Eject a small amount of adhesive. This must be done so that the two components mix as effectively as possible. Now apply a bead of adhesive onto the block. Place the block quickly onto the pre-prepared, clean and dry, healthy hoof. After around 30 seconds, the adhesive will have set, and after around 2-3 minutes, the hoof can weight-bear again.

Sets include:
1 x 160 ml cartridge with 2-part adhesive
10 x mixing tips
10 x wooden blocks XL

1 x dispensing gun

Technovit-2-Bond / 16239
The fast, 2-part PU adhesive for hoof treatment!

The benefits at a glance:

• dries within 30 seconds
• can be used at a 45° and a 90° angle
• the hoof can bear full weight again after approx. 3 minutes (if stored correctly over 15° C)
• bonds powerfully and permanently to wood and rubber blocks
• easy to use - no mixing, no waste

Here's how simple it is to use: Remove the seal on the cartridge and connect up the mixing tip. Eject a small amount of adhesive. This must be done so that the two components mix as effectively as possible. Now apply a bead of adhesive onto the block. Place the block quickly onto the pre-prepared, clean and dry, healthy hoof. After around 30 seconds, the adhesive will have set, and after around 2-3 minutes, the hoof can weight-bear again.

Sets include:
1 x 160 ml cartridge with 2-part adhesive
10 x mixing tips
10 x wooden blocks XL

1 x dispensing gun

Technovit-2-Bond / 16239
The fast, 2-part PU adhesive for hoof treatment!

The benefits at a glance:

• dries within 30 seconds
• can be used at a 45° and a 90° angle
• the hoof can bear full weight again after approx. 3 minutes (if stored correctly over 15° C)
• bonds powerfully and permanently to wood and rubber blocks
• easy to use - no mixing, no waste

Here's how simple it is to use: Remove the seal on the cartridge and connect up the mixing tip. Eject a small amount of adhesive. This must be done so that the two components mix as effectively as possible. Now apply a bead of adhesive onto the block. Place the block quickly onto the pre-prepared, clean and dry, healthy hoof. After around 30 seconds, the adhesive will have set, and after around 2-3 minutes, the hoof can weight-bear again.

Sets include:
1 x 160 ml cartridge with 2-part adhesive
10 x mixing tips
10 x wooden blocks XL

1 x dispensing gun

Technovit-2-Bond / 16239
The fast, 2-part PU adhesive for hoof treatment!

The benefits at a glance:

• dries within 30 seconds
• can be used at a 45° and a 90° angle
• the hoof can bear full weight again after approx. 3 minutes (if stored correctly over 15° C)
• bonds powerfully and permanently to wood and rubber blocks
• easy to use - no mixing, no waste

Here's how simple it is to use: Remove the seal on the cartridge and connect up the mixing tip. Eject a small amount of adhesive. This must be done so that the two components mix as effectively as possible. Now apply a bead of adhesive onto the block. Place the block quickly onto the pre-prepared, clean and dry, healthy hoof. After around 30 seconds, the adhesive will have set, and after around 2-3 minutes, the hoof can weight-bear again.

Sets include:
1 x 160 ml cartridge with 2-part adhesive
10 x mixing tips
10 x wooden blocks XL

1 x dispensing gun

Technovit-2-Bond / 16239
The fast, 2-part PU adhesive for hoof treatment!

The benefits at a glance:

• dries within 30 seconds
• can be used at a 45° and a 90° angle
• the hoof can bear full weight again after approx. 3 minutes (if stored correctly over 15° C)
• bonds powerfully and permanently to wood and rubber blocks
• easy to use - no mixing, no waste

Here's how simple it is to use: Remove the seal on the cartridge and connect up the mixing tip. Eject a small amount of adhesive. This must be done so that the two components mix as effectively as possible. Now apply a bead of adhesive onto the block. Place the block quickly onto the pre-prepared, clean and dry, healthy hoof. After around 30 seconds, the adhesive will have set, and after around 2-3 minutes, the hoof can weight-bear again.

Sets include:
1 x 160 ml cartridge with 2-part adhesive
10 x mixing tips
10 x wooden blocks XL

1 x dispensing gun